Greg's take on this chapter
This is the longest, densest chapter in the whole book — take it one unit process at a time. Notice how the processes chain together: aeration removes gases and oxidizes iron/manganese, coagulation/flocculation clumps particles, sedimentation settles the heavy floc out, and filtration polishes what's left. Learn the numbers for each stage and you'll be able to answer almost anything thrown at you.
1 Aeration
Aeration mixes air into water to remove troublesome gases (carbon dioxide, hydrogen sulfide, methane), oxidize iron and manganese into a removable insoluble form, reduce certain tastes and odors, and add oxygen. Water containing more than 0.3 mg/l iron stains fixtures and clothing yellowish-brown; manganese above 0.05 mg/l can produce black stains. Aeration followed by 30 minutes of detention time oxidizes these metals, and filtration then removes the precipitate. Loading rates for gravity aerators run 10-30 gpm/ft². Hydrogen sulfide is dangerous in enclosed spaces — concentrations of just 0.1% gas-to-air can be fatal within 30 minutes — so adequate ventilation is essential.
2 Coagulation and flocculation
Most particles causing turbidity carry a negative charge and repel each other (the zeta potential). Coagulation is the rapid mixing of a positively-charged coagulant into the water to neutralize that charge — this reaction happens in one to two seconds, which is exactly why rapid mixing is so critical. Flocculation is the gentle mixing afterward that lets neutralized micro-floc collide and grow into larger, settleable floc.
Coagulants are classified by charge: monovalent (1+), bivalent (2+), and trivalent (3+, like aluminum and iron) — trivalent coagulants are 700 to 1,000 times more effective than monovalent ones at neutralizing negative particles. Alum (aluminum sulfate) is the most common coagulant.
3 Sedimentation
Sedimentation settles out the heavier floc before filtration, ideally leaving effluent turbidity under 10 NTU. Every settling basin has four zones — inlet, settling, outlet, and sludge. Design criteria call for a minimum of four hours detention time (reduced to two hours for lime-soda softening treating only ground water), settling velocity under 0.5 ft/min, and a weir overflow rate not exceeding 20,000 gallons per day per foot of weir length. A typical overflow rate for alum floc is about 500 gpd/ft².
4 Filtration
Filtration is the last polishing step before water reaches customers. Most Mississippi plants use gravity, downflow rapid sand or dual-media (sand + anthracite) filters. Typical loading rates: about 2 gpm/ft² for single-media, 3 gpm/ft² for dual-media filters. Backwash when head loss reaches 7 to 10 feet, at rates of 15-20 gpm/ft² for sand filters or 10-15 gpm/ft² for dual media, typically for 3-20 minutes until the wash water runs clear.
5 Ion exchange, iron/manganese control, and stabilization
Ion exchange swaps one ion for another — usually sodium for calcium/magnesium (softening). It works best for low-hardness, low-TDS water (under 2,000 mg/l) and isn't suitable above 0.3 mg/l iron or manganese combined. Regeneration uses a strong salt (brine) solution over 20-35 minutes of contact time.
Iron and manganese control methods include oxidation/detention/filtration, water softening, manganese greensand filtration, ion exchange, and polyphosphate sequestration. Potassium permanganate oxidizes manganese faster than chlorine and works across pH 5-9.
Stabilization keeps finished water from being corrosive or scale-forming — the Langelier Saturation Index predicts which way a given water will go, valid within a pH range of 6.5-9.5. A slightly positive index deposits a thin, protective calcium carbonate coating on pipe walls; a negative index means corrosive water.
6 Aerators in practice
Aerators come in several types: cascade and tray aerators, where water tumbles over steps or trickles through stacked trays; forced-draft towers, where a fan blows air up through falling water; spray aerators; and diffused-air systems that bubble air up through a tank. Removing carbon dioxide raises the pH, which speeds iron oxidation and makes water less corrosive.
- Clean trays and media regularly. Iron deposits and slime cut the surface area and hurt removal.
- Keep screens on air inlets and vents to stop birds, insects, and debris. Aerated water has been open to the air, so disinfect after aeration.
- Ventilate aerator buildings. Hydrogen sulfide released by aeration is toxic, and methane is explosive.
- Check pH and iron before and after the aerator to confirm it's working.
7 Filter operation and backwashing
Watch three things during a filter run: head loss, effluent quality (turbidity, or iron and manganese at a removal plant), and run time. End the run when head loss reaches its limit (7–10 feet in the manual), when effluent quality starts to slip (breakthrough), or when the run hits its maximum time.
A typical backwash:
- Take the filter offline and drain it down to just above the media.
- Run the surface wash for a minute or two to break up the top layer.
- Start the backwash slowly so the gravel isn't disturbed, then raise it to the full rate, expanding the bed about 20–50%.
- Wash until the water runs nearly clear, then lower the rate gradually so the media settles back in layers.
- Filter to waste until the effluent is back within limits, then return the filter to service.
Trouble signs: mudballs and cracks (not enough backwashing), media washing into the troughs (backwash rate too high), and air binding (air coming out of solution inside the bed when head loss gets so high that the pressure there drops below atmospheric).
8 Pressure filters and greensand for iron and manganese
Many small Mississippi systems remove iron and manganese with pressure filters: closed steel tanks of media that run at system pressure, so water doesn't have to be pumped twice. An oxidant (chlorine, permanganate, or air) is added ahead of the filter, and the media catches the particles that form.
- Manganese greensand and similar coated media hold a manganese oxide coating that oxidizes and captures iron and manganese. The coating is kept up with potassium permanganate, either fed continuously ahead of the filter or used to regenerate the bed.
- Pink water means too much permanganate. Cut the feed and flush.
- Backwash on schedule, or when the pressure drop across the filter rises, at the manufacturer's rate.
- Test iron and manganese in the filter effluent regularly, and inspect the media once a year for mudballs, channeling, or media loss.
You can't see inside a pressure filter, so inlet and outlet gauges and good records are your eyes. A filter that never shows a pressure drop may be channeling instead of filtering.
📌 Numbers Greg wants you to memorize
- Iron over 0.3 mg/l stains; manganese over 0.05 mg/l stains black.
- Coagulation reaction time: 1-2 seconds — rapid mixing is critical.
- Trivalent coagulants are 700-1,000× more effective than monovalent ones.
- Sedimentation: minimum 4 hours detention (2 hrs for lime-soda softening); effluent turbidity target <10 NTU.
- Filter backwash trigger: head loss of 7-10 feet.
- Filtration rates: ~2 gpm/ft² single media, ~3 gpm/ft² dual media.
- Backwash bed expansion about 20–50%; filter to waste before returning to service.
- Pink water = permanganate overfeed.
Words to know for Chapter 8 (B&C)
Plain-language definitions from the LearnWater glossary.
Quick check: 5 questions
Random questions from this chapter's bank. Your answers count toward your progress in the Learning Center.
Tap a card to flip it
Questions about Chapter 8 (B&C)?
Greg answers from the operators manual and works formulas right in your browser. Ask him to search EPA, NRWA, or MsRWA and only your search words go to that site.