Chapter 3 · Mississippi Waterworks Operators Manual

Mathematics

The conversions, formulas, and worked examples every operator leans on — from unit conversions to area, volume, and dosage calculations.

Greg's take on this chapter

Don't panic — this chapter is mostly arithmetic wrapped in water-plant vocabulary. Memorize the area/volume formulas and the 8.34 conversion factor and you can solve most of the math questions on any class exam. When in doubt, convert everything to the same units before you calculate anything.

1 Pure vs. concrete numbers, and units

A pure number has no units (26, 195, ¾). A concrete number has specific units attached (26 psi, 195 gallons, 7.48 gallons per cubic foot). Always convert concrete numbers to the same units before calculating anything with them. Common water-industry units include pounds per day (ppd), gallons per minute (gpm), milligrams per liter (mg/l), and pounds per square inch (psi); larger Class A/B/C plants also use gallons per square foot, pounds per gallon, and million gallons per day (mgd).

2 Fractions, decimals, and percentages

To add or subtract fractions, first find a common denominator. To multiply fractions, multiply numerators together and denominators together. To divide, invert the divisor and multiply. For decimals: line up decimal points to add/subtract; multiply as whole numbers then count total decimal places to place the point; to divide, move the divisor's decimal point to the end, and move the dividend's decimal point the same number of places.

To turn a decimal into a percent, move the decimal point two places right (0.50 → 50%). To turn a percent into a decimal, move it two places left. To find a percentage of a number, multiply by the decimal form (20% of 50 = 0.20 × 50 = 10).

3 Exponents, ratio, proportion, and averages

Exponentiation means multiplying a number by itself: 2² = 2×2 = 4, and 2³ = 2×2×2 = 8. A ratio (X:Y or X/Y) compares two numbers; a proportion is a statement that two ratios are equal, and you can cross-multiply to solve for an unknown — this is the basis of every dosage-rate calculation you'll do. An average is the sum of a data set divided by how many values are in it — used constantly for average daily demand, pump run times, and storage turnover.

4 Area, perimeter, and volume

Area is two dimensions multiplied together; volume is three. Always keep units consistent (convert inches to feet, etc., before multiplying). Key formulas:

ShapeFormula
Rectangle areaLength × Width
Circle areaπ × D² ÷ 4 (π ≈ 3.14)
Circle perimeterπ × D
Rectangular tank volumeW × L × H
Cylindrical tank volume3.14 × r² × H

Example: a box 3 ft tall, 2 ft wide, 5 ft long has a volume of 3 × 2 × 5 = 30 cubic feet. A circular filter with a 20-foot diameter has an area of 3.14 × 10² = 314 square feet.

5 The 8.34 conversion — dosage math

One gallon of water weighs 8.34 pounds. That single number is the key to almost every chemical dosage problem you'll see: a dosage of 1 mg/l (= 1 ppm) in one million gallons of water equals 8.34 pounds of chemical. So for a chlorine feed of 5 ppm, you'd need 5 × 8.34 = 41.7 pounds of chlorine per million gallons treated. If the chemical isn't 100% pure — say 65% available chlorine like HTH — divide the pounds needed by the purity fraction to find how much actual product to feed.

6 Conversion factors to know by heart

To convertUse
Cubic feet to gallons× 7.48
Gallons of water to pounds× 8.34
gpm to gallons per day× 1,440
MGD to gpm× 694.4
Cubic feet per second (cfs) to gpm× 448.8
psi to feet of head× 2.31
Feet of head to psi× 0.433
Gallons to liters× 3.785
Grains per gallon to mg/L× 17.1
Percent strength to mg/L1% = 10,000 mg/L

Write the units next to every number and let them guide you. If you need gallons and your answer comes out in cubic feet, multiply by 7.48. If the units don't cancel the way you expect, the setup is wrong.

7 Flow, velocity, and detention time

Three formulas handle most flow problems:

  • Flow = Area × Velocity (Q = A × V). With area in ft² and velocity in ft/sec, Q comes out in cubic feet per second.
  • Detention time = Volume ÷ Flow. Match the time units: gallons ÷ gpm gives minutes; gallons ÷ gpd gives days.
  • Circle area = 0.785 × D² with D in feet. It's the same as π × D² ÷ 4.

Example: velocity. A 6-inch main carries 300 gpm. Flow: 300 ÷ 448.8 = 0.668 cfs. Area: 0.785 × (0.5 ft)² = 0.196 ft². Velocity = 0.668 ÷ 0.196 = 3.4 ft/sec.

Example: detention time. A clearwell holds 50,000 gallons and the plant runs at 250 gpm. Detention time = 50,000 ÷ 250 = 200 minutes, about 3.3 hours.

8 Chemical feed problems, step by step

Use the same five steps on every word problem: (1) list what you know, with units; (2) decide what you're solving for; (3) convert to matching units; (4) plug into the formula; (5) ask whether the answer makes sense.

Example. A well pumps 350 gpm for 16 hours a day, and you want a chlorine dose of 1.5 mg/L using 65% HTH.

  1. Daily flow: 350 gpm × 60 min × 16 hr = 336,000 gal = 0.336 MGD.
  2. Chlorine: 1.5 mg/L × 0.336 MGD × 8.34 = 4.2 lb/day.
  3. HTH: 4.2 ÷ 0.65 = 6.5 lb/day.

Dose = demand + residual. If water has a chlorine demand of 1.8 mg/L and you want 0.6 mg/L left over, feed 2.4 mg/L.

Dilution: C₁ × V₁ = C₂ × V₂. To make 50 gallons of 2% chlorine solution from 12.5% bleach: V₁ = (2 × 50) ÷ 12.5 = 8 gallons of bleach plus 42 gallons of water.

📌 Numbers Greg wants you to memorize

  • 8.34 lbs — weight of one gallon of water; the basis for every dosage calculation.
  • 1 mg/l = 1 ppm — and equals 8.34 lbs of chemical per million gallons of water.
  • π ≈ 3.14 — used in every circle/cylinder area and volume formula.
  • Circle area = π × D² ÷ 4; cylinder volume = 3.14 × r² × H.
  • 7.48 gallons per cubic foot — the conversion between cubic feet and gallons.
  • 1 MGD = 694.4 gpm; 1 cfs = 448.8 gpm; 1,440 minutes in a day.
  • 1% = 10,000 mg/L; 1 grain per gallon = 17.1 mg/L.
  • Circle area = 0.785 × D²; detention time = volume ÷ flow; Q = A × V.
  • Dilution: C₁ × V₁ = C₂ × V₂.
Key terms

Words to know for Chapter 3

Plain-language definitions from the LearnWater glossary.

Open the full glossary →

Check yourself

Quick check: 5 questions

Random questions from this chapter's bank. Your answers count toward your progress in the Learning Center.

Flash cards

Tap a card to flip it

Study these in the flash card trainer →

Ask Greg

Questions about Chapter 3?

Greg answers from the operators manual and works formulas right in your browser. Ask him to search EPA, NRWA, or MsRWA and only your search words go to that site.

Finished this chapter?Mark it complete to update your progress.